Welcome to the forums. Please post in English or French.

You are not logged in.

#1 2019-05-18 12:01:25

nirmaljoshi
Member
From: Japan
Registered: 2018-10-12
Posts: 152

ERROR in documentation

Hi everyone, I am starting this thread to report error in documentation files. May be this post should be made sticky so that everyone can see and post it. I also hope the developers will update the documents.

Offline

#2 2019-05-18 12:03:54

nirmaljoshi
Member
From: Japan
Registered: 2018-10-12
Posts: 152

Re: ERROR in documentation

Location:
U3.11.01 Page 7

Error:
.........Non-linear statics SSLS111B...

Rectification:
SSLS111B should be SSNL111

Offline

#3 2019-07-11 15:59:14

argi
Member
From: Bidart FRANCE
Registered: 2019-01-10
Posts: 12

Re: ERROR in documentation

POSSIBLE ERROR in U4.81.01, Documentation for CALC_ELEM, page 15/27

EPSP is "Déformations anélastiques aux points de Gauss" as is written on the documentation, or is it the PLASTIQUE STRAIN?
Regarding the symbol I would say that it is the plastique strain and not anelastique strain!

In Documentation for CALC_CHAMP, page 14/31 there is the same situation!

In addition, in u4.83.02, Documentation for CALC_FATIGUE, in page 13/27 EPSP_ELGA is considered as plastique strain!

Can someone clarify my doubt?

Thank you!

Last edited by argi (2019-07-11 16:16:51)

Offline

#4 2019-07-16 14:43:31

Anirudh
Member
Registered: 2017-09-11
Posts: 246

Re: ERROR in documentation

Hello,
There seems to be a typographic error in AFFE_CARA_ELEM documentation(u4.42.01) Page 31.
The error is under Opérande CARA = ’ANGL_VRIL’.
The text is , "...transformant ( P , x3, x 2, x2 ) en ( P , x3, y3, z3)"...
whereas it should be "...transformant ( P , x3, y2, z2 ) en ( P , x3, y3, z3)..."


Regards
Anirudh

Offline

#5 2019-08-28 04:43:24

nirmaljoshi
Member
From: Japan
Registered: 2018-10-12
Posts: 152

Re: ERROR in documentation

Document U4.43.01 DEFI_MATERIAU

Section 7.21 Keyword BETON_RAG
The syntax given below do not match with the code aster/salome meca input. Instead it is something as shown in attached snapshot.


/ BETON_RAG = _F(
Characteristics for the mechanical behavior damage
♦ ENDO_MC = meca_mc [R]
♦ ENDO_MT = meca_mt [R]
♦ ENDO_SIGUC = meca_siguc [R]
♦ ENDO_SIGUT = meca_sigut [R]
♦ ENDO_DRUPRA = will meca_drupra [R]
Characteristics of creep
♦ FLUA_SPH_KR = flua_sph_kr [R]
♦ FLUA_SPH_KI = flua_sph_ki [R]
♦ FLUA_SPH_NR = flua_sph_nr [R]
♦ FLUA_SPH_NI = flua_sph_ni [R]
♦ FLUA_DEV_KR = flua_dev_kr [R]
♦ FLUA_DEV_KI = flua_dev_ki [R]
♦ FLUA_DEV_NR = flua_dev_nr [R]
♦ FLUA_DEV_NI = flua_dev_ni [R]
Characteristics of L has formation of the gels and of the RAG
♦ GEL_ALPHA0 = gel_alpha0 [R]
♦ GEL_TREF = gel_tref [R]
♦ GEL_EAR = gel_ear [R]
♦ GEL_SR0 = gel_sr0 [R]
♦ GEL_VG = gel_vg [R]
♦ GEL_MG = gel_mg [R]
♦ GEL_BG = gel_bg [R]
♦ GEL_A0 = gel_a0 [R]
♦ RAG_EPSI0 = rag_epsi0 [R]
♦ PW_A = pw_a [R]
♦ PW_B = pw_b [R]
)


Attachments:
beton_rag.JPG, Size: 30.14 KiB, Downloads: 23

Offline