Welcome to the forums. Please post in English or French.

You are not logged in.

#1 2021-04-15 16:49:08

kaengo
Member
From: Germany - Schleswig-Holstein
Registered: 2016-11-25
Posts: 30

Salome-Meca 2020.0.1 on Suse SLED 15 SP2

Salut
I trie it again....
(Sorry, i MUST use Suse or RedHat rep. CentOS, because until now I do the most part of my work with ANSYS.)

On my Suse SLED 15 SP2, Salome-Meca 2019 runs fine,
but 2020 crashes direct after start with the message

holger@kraehe:~/salome_meca/appli_V2020.0.1_universal_universal> ./salome
runSalome running on kraehe
Searching for a free port for naming service: 2828 - OK
inside europlexus set env...
omniNames: (0) 2021-04-15 17:47:55.584379: -ORBendPoint option overriding default endpoint.
Searching Naming Service  + found in 0.1 seconds
Warning, no type found for resource "localhost", using default value "single_machine"
Searching /Kernel/Session in Naming Service  +++Warning: this type (Study,objref) already exists, it will be ignored.
Warning: this type (SALOME_MED/MEDCouplingFieldDoubleCorbaInterface,objref) already exists, it will be ignored.
found in 1.5 seconds
Start SALOME, elapsed time :  20.4 seconds
****************************************************************
     Warning: module BLSURFPLUGIN is improperly configured!
     Module BLSURFPLUGIN will not be available in GUI mode!
****************************************************************
****************************************************************
     Warning: module HYBRIDPLUGIN is improperly configured!
     Module HYBRIDPLUGIN will not be available in GUI mode!
****************************************************************
****************************************************************
     Warning: module GMSHPLUGIN is improperly configured!
     Module GMSHPLUGIN will not be available in GUI mode!
****************************************************************
****************************************************************
     Warning: module NETGENPLUGIN is improperly configured!
     Module NETGENPLUGIN will not be available in GUI mode!
****************************************************************
****************************************************************
     Warning: module HexoticPLUGIN is improperly configured!
     Module HexoticPLUGIN will not be available in GUI mode!
****************************************************************
****************************************************************
     Warning: module GHS3DPLUGIN is improperly configured!
     Module GHS3DPLUGIN will not be available in GUI mode!
****************************************************************
th. 140083719115328 - Trace /home/A34370/smeca/yamm_build/V2020.0.1_universal_build/V2020_nopackage_universal/modules/src/GUI/src/LightApp/LightApp_Application.cxx [807] :
****************************************************************
     Warning: icon for Calculator is not found!
     Using the default icon.
****************************************************************

*** Abort *** an exception was raised, but no catch was found.
        ... The exception is:SIGSEGV 'segmentation violation' detected. Address 8
holger@kraehe:~/salome_meca/appli_V2020.0.1_universal_universal> Terminating SALOME on port 2828...


Does anybody know,
what is wrong here?

Holger

Offline

#2 2021-08-09 17:12:22

msh
Member
Registered: 2021-08-04
Posts: 8

Re: Salome-Meca 2020.0.1 on Suse SLED 15 SP2

I think, I have same running errors in my topic: viewtopic.php?id=25836, but I have no solution now how resolve it.

Offline

#3 2021-08-09 22:28:50

kaengo
Member
From: Germany - Schleswig-Holstein
Registered: 2016-11-25
Posts: 30

Re: Salome-Meca 2020.0.1 on Suse SLED 15 SP2

Your link seems not to work.
At this time, the question is not relevant for me.
(But I think, it will still come...)

Maybe, I can switch to Ubuntu in the next years.
(Because, it seems, ANSYS will also support Ubuntu in next years)

Greetings,
Holger

Offline