Welcome to the forums. Please post in English or French.

You are not logged in.

#1 2008-11-11 16:49:06

Warren_G
Member
Registered: 2008-09-29
Posts: 20

Test case sslp105a - Adding Thermal Conditions

Hello,

I am looking at adapting test case sslp105a (excavation of a tunnel) to include thermal conditions. I have added thermal conditions to the initial static non linear problem in the command file. The problem solves with alarms and provides a temperature distribution across the ground, although there doesn't seem to be an interaction between the material properties and the thermal conditions applied i.e. no change in the stress distribution across the ground. The following error occurs when solving the problem.

   !--------------------------------------------------------------------------------!
   ! <A> <MECANONLINE2_97>                                                          !
   !                                                                                !
   !                                                                                !
   !   -> Les variables de commandes initiales induisent des contraintes            !
   !      incompatibles :                                                           !
   !      l'état initial (avant le premier instant de calcul) est tel que           !
   !      les variables de commande (température, hydratation, séchage...)          !
   !      conduisent à des contraintes non équilibrées.                             !
   !                                                                                !
   !   -> Indications supplémentaires : pour la variable de commande :  TEMP        !
   !      et la composante :  TEMP                                                  !
   !      Valeur maximum de abs( TEMP - TEMP_REF) : 5.000000 sur la maille : MA1120 !
   !      Valeur minimum de abs( TEMP - TEMP_REF) : 0.000000 sur la maille : MA1    !
   !                                                                                !
   !   -> Risque & Conseil :  dans le cas d'une résolution incrémentale,            !
   !      on ne considère que la variation des variables de commande entre          !
   !      l'instant précédent et l'instant actuel.                                  !
   !      On  ne prend donc pas en compte d'éventuelles contraintes incompatibles   !
   !      dues à ces variables de commande initiales.                               !
   !      Pour tenir compte de ces contraintes vous pouvez :                        !
   !      - partir d'un instant fictif antérieur où toutes les variables de         !
   !        commande sont nulles ou égales aux valeurs de référence                 !
   !      - choisir des valeurs de référence adaptées                               !
   !      Pour plus d'informations, voir la documentation de STAT_NON_LINE          !
   !      (U4.51.03) mot-clé EXCIT, et le test FORMA09 (V7.20.101).                 !
   !                                                                                !
   !                                                                                !
   !                                                                                !
   ! Ceci est une alarme. Si vous ne comprenez pas le sens de cette                 !
   ! alarme, vous pouvez obtenir des résultats inattendus !                         !
   !--------------------------------------------------------------------------------!

Any help you could provide on this problem would be of great help. Attached is the command file for the problem.

Regards,

Warren


Attachments:
sslp105a_EL2.comm, Size: 15.9 KiB, Downloads: 331

Offline

#2 2008-12-05 14:11:04

Thomas DE SOZA
Guru
From: EDF
Registered: 2007-11-23
Posts: 3,066

Re: Test case sslp105a - Adding Thermal Conditions

Hi,

With some delay (I'm reviewing unanswered posts) I had a look at your message. It may be due to a bug which was solved in version 9.3.1. You should try to update your Code_Aster version to 9.3.25 (the last one, see the forum or the wiki on how to do that) or you can wait for the package of the 9.4 version to come out (soon).

TdS

Offline